Download Article

Download Article

This is how to make a cool airsoft gun out of a Nerf gun. Note: the bigger the gun the better; a pump Nerf gun gives you lot more fps (feet per sec).

Steps

  1. i

    Get a Nerf gun; any will do.

  2. 2

    Get a Nerf Dart (the ammo for Nerf gun) and pull the end off of information technology. You lot will accept a foam tube.

    Advertisement

  3. iii

    Get a Bic pen and use pliers to accept out the back and front end so you have a tube.

  4. iv

    Stick the Bic pen tube into the cream tube; almost half of the pen should be covered by the dart.

  5. 5

    Place the dart end into the butt, button downward on the dart as far as yous tin can, and so push button the pen tube into the barrel.

  6. 6

    Cock and shoot cypher a few times to ensure that it doesn't autumn out.

  7. 7

    Cock and shoot at your hand, if air pressure level is nowadays, adept chore!

    Advertising

Add together New Question

  • Question

    Does this work with any Nerf gun?

    TaterBoi

    TaterBoi

    Community Reply

    Aye, this method will work for any front-loading Nerf blasters.

  • Question

    Volition a copper BB work?

    Community Answer

    It may, just it is a little smaller than the Airsoft BB. If information technology doesn't work, you could try using a smaller pen tube.

  • Question

    How tin can I practise this with a Sharpfire?

    Community Answer

    You lot cannot, unfortunately. The Sharpfire is impossible to modify in this way.

  • Question

    How do I make an Airsoft gun out of a Nerf rifle that shoots balls?

    Community Answer

    Block off all forms of air escape except the barrel, and use a straw or pen tube there. Make sure air goes through the tube.

  • Question

    How do I make this ane with the Retaliator?

    Viktor Simbulan

    Viktor Simbulan

    Customs Reply

    It might be hard to make it with a Retaliator since it is clip-fed. Try a Jolt, or any other front-loaders.

  • Question

    Can I use the Nerf RaptorStrike to do this? If so, how?

    Community Answer

    No, information technology is a prune loader and then it probably wouldn't work. Endeavor a front-loader, similar a Jolt.

  • Question

    Can I apply a straw instead of a pen tube to brand an Airsoft gun out of a Nerf gun?

    Community Answer

    Yes you can they will both work the same, just don't twist or bite the harbinger.

  • Question

    How exercise I take the height of a dart off?

    Community Answer

    This is like shooting fish in a barrel; just rip it off or cutting it with scissors. It'due south that simple.

  • Question

    What should I use for ammunition?

    Community Answer

    Airsoft Bulletin board system are used.

  • Question

    Do I take to use a pen to practise this?

    Community Answer

    No. Any tube that fits will work. Simply follow the instructions above to arrive.

Show more answers

Enquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

  • The pen tube will stay in better if the tape on the end is crumpled a niggling.

  • You tin can paint your gun black like a normal Airsoft gun if you lot want, but to stay legal leave the orange tip.

  • Make sure you don't hitting anyone unless you are in an Airsoft state of war.

Thanks for submitting a tip for review!

Advertizement

Things You'll Need

  • Nerf gun (any)
  • Pen medium
  • Tape (whatsoever)
  • Ammo (annihilation that fits well in the pen tube)

About This Article

Thanks to all authors for creating a page that has been read 97,893 times.

Did this article assist you?